Hogue OverMolded Rubber Bantam Grip Closed Backstrap SW Round Butt J Frame Revolvers Black 61020 HA61020 UPC 743108610206
Product Description
Tame the violent snap of high-pressure defensive wheelguns with the Hogue® OverMolded® Rubber Bantam Grip with Closed Backstrap for Smith & Wesson® Round Butt J-Frames (SKU: 61020 / UPC: 743108610206). Designed specifically for concealable snub-nose revolvers chambered in .38 Special, .38 Special +P, and .357 Magnum, this innovative upgrade solves the primary handling flaw of micro revolvers: excessive recoil impulse directed into the web of the firing hand. By enclosing the rear metal frame spine in resilient, shock-absorbing rubber, the Bantam Closed Backstrap (CBS) model delivers superior shooting endurance without compromising everyday deep-concealment carry.
Constructed through Hogue’s patented multi-stage molding process, the grip features a durable thermoplastic elastomer (TPE) skin molded over a rigid, fiberglass-reinforced polypropylene skeleton. This synthetic compound is totally impervious to petroleum-based solvents, aggressive aerosol cleaners, weapon lubricants, and skin acids, ensuring the rubber will never degrade, peel, or become tacky over years of duty use. The grip flanks and front strap are covered in Hogue’s renowned Cobblestone™ texturing, which provides mechanical traction that locks into damp or gloved hands without grabbing shirts or pocket linings during the draw stroke.
Unlike traditional aftermarket revolver stocks that add unnecessary bulk below the heel, the Bantam CBS profile introduces an extended lower finger groove shelf that allows all three fingers to secure a firm, positive lock on the weapon. Utilizing Hogue’s patented screwless snap-on attachment design, the grip secures directly to the revolver frame’s internal stock pin without requiring stirrups, retaining screws, or external hardware. The result is a smooth, snag-free exterior envelope that maximizes control, accelerates double-action follow-up shots, and enhances weapon retention under high-stress defensive conditions.
*Armorer Bench Notes & Real-World Staging Guidance:*
Fitment Matrix: Precision fit for all Smith & Wesson Round Butt J-Frame revolvers (Airweight, Airlite, and all-steel Centennial, Chief's Special, and Bodyguard configurations) and Diamondback SDR revolvers. CRITICAL WARNING: Will NOT fit vintage S&W J-Frame Square Butt frames, K/L/N/X-frame revolvers, or polymer-chassis S&W M&P Bodyguard 38 models. This grip does NOT utilize mounting screws or frame stirrups; it snaps directly over the factory lower grip frame pin. Never force or pry the grip with metallic screwdrivers, as this can mar the revolver frame or slice the internal elastomer retaining tabs.
- Ensure the host firearm is completely clear, swing the cylinder fully open, visually and physically inspect all five cylinder chambers, and verify the revolver is unloaded.
- Remove the factory grip panels by unscrewing the central grip screw (or removing the factory pin/stocks), ensuring the lower factory grip locator roll pin remains centered in the lower frame tang.
- Clean and degrease the lower frame handle to eliminate old lubrication, lead residue, and lint before beginning installation.
- Insert the included Hogue plastic installation spreader tool (or two smooth non-marring shims) into the top rear split of the Bantam grip to slightly spread the internal retaining detents.
- Slide the expanded Bantam grip upward and forward over the bottom of the frame until the internal molded channels fully seat and snap lock over the frame locator pin, withdraw the spreader tool, and cycle double-action dry fire to verify absolute clearance around the trigger guard and cylinder release.
Key Features
- Closed Backstrap Recoil Attenuation: Cushioned rubber spine completely encloses the metal backstrap, dispersing felt impulse and eliminating web-of-the-hand bone bruise from .38 +P and .357 Mag loads.
- Patented Screwless Snap-On Architecture: Secures firmly to the factory lower stock pin without cumbersome screws, stirrups, or exposed hardware for an ultra-clean, snag-free carry profile.
- Full Three-Finger Purchase: Ergonomic front finger grooves provide a dedicated resting shelf for the pinky finger, eliminating muzzle flip without adding unmanageable grip length.
- Cobblestone™ Surface Pattern: Multi-directional micro-stippling guarantees a non-slip purchase in rain, sweat, or extreme tactical conditions without abrading concealed carry clothing.
- Solvent & Chemical Impervious Elastomer: Engineered from proprietary synthetic thermoplastic rubber that resists degradation from gun oils, bore solvents, and skin acids.
- Rigid Synthetic Internal Frame: Durable fiberglass-reinforced inner skeleton prevents grip twisting, squirming, or separation from the steel frame during dynamic weapon handling.
Product Specifications
- Brand: Hogue®
- Model/Series: OverMolded® Rubber Bantam Grip - Closed Backstrap (CBS)
- MPN / SKU: 61020 / HA61020
- UPC: 743108610206
- Platform Compatibility: Smith & Wesson® J-Frame Revolvers (Round Butt Models Only) & Diamondback SDR
- Frame Size: Small Frame (J-Frame)
- Material Construction: Synthetic Thermoplastic Elastomer OverMolded on Rigid Polymer Core
- Texture / Pattern: Cobblestone™ Stippling
- Color / Finish: Non-Reflective Matte Black
- Attachment Style: Patented Snap-On (Screwless / No Stirrup)
- Country of Origin: United States
