*CONTACT US FOR A SPECIAL COUPON CODE*
Trijicon MRO SD 1x25 Red Dot Sight w 3x Magnifier Combo Black MRO C 2200367 UPC 719307621923
Product Description
The Trijicon® MRO® SD 1x25 Red Dot Sight with 3x Magnifier Combo (SKU: MRO-C-2200367 / UPC: 719307621923) is a duty-grade close-to-mid-range optical system engineered for AR-15 carbines, patrol rifles, and modern sporting platforms. Combining the re-engineered MRO SD 2.0 MOA red dot reflex sight with Trijicon's compact 3x flip-to-side magnifier, this factory-matched kit delivers rapid 1x both-eyes-open target acquisition and instant 3x magnification for positive target identification and extended-range precision.
Forged from 7075-T6 aircraft-grade aluminum and protected by a corrosion-resistant matte black hardcoat anodized finish, both the MRO SD and 3x magnifier are built to survive severe impact, heavy recoil, and harsh environmental exposure. The MRO SD housing is dry-nitrogen purged and waterproof to 100 feet (30 meters), while its re-engineered multicoated objective lens minimizes optical distortion and delivers crisp dot resolution when viewed through the 3x magnifier. Sub-flush, capless adjusters prevent snag hazards and accidental zero shifts while providing tactile 1/2 MOA clicks across 70 MOA of total travel.
Designed for seamless modularity on MIL-STD-1913 Picatinny rails, the MRO SD ships pre-configured on a Trijicon Q-LOC™ Quick-Release Full Co-Witness Mount alongside a quick-release flip-to-side magnifier mount engineered to clear standard rear backup iron sights. An included magnifier riser plate and fastener set allow operators to configure optical centerline alignment for either Full Co-Witness or Lower 1/3 Co-Witness setups right out of the box.
*Armorer Bench Notes & Real-World Staging Guidance:*
Fitment Matrix: Compatible with MIL-STD-1913 Picatinny upper receivers on AR-15/M4, AR-10/SR-25, and tactical carbine platforms utilizing standard AR-height iron sights. CRITICAL: Both optics must be mounted strictly to the monolithic or upper receiver Picatinny rail—never bridge the MRO SD mount onto a free-float handguard, which will induce zero shift under barrel/rail flex. The Trijicon 3x Magnifier uses a proprietary base footprint and will NOT fit Aimpoint, EOTech, or third-party 2-bolt/30mm ring magnifier mounts.
- Ensure the host firearm is completely clear, magazine removed, and chamber visually and physically verified empty.
- Degrease the upper receiver's MIL-STD-1913 Picatinny rail slots and verify whether you are running Full Co-Witness (default) or Lower 1/3 Co-Witness (install the included riser plate between the 3x magnifier body and flip-to-side mount using the provided fasteners).
- Position the MRO SD Q-LOC™ Full Co-Witness mount forward on the upper receiver rail (without bridging onto the handguard), push the recoil lugs firmly forward against the Picatinny slot walls, and lock the Q-LOC™ lever to spec.
- Install the 3x Magnifier Flip-to-Side mount immediately behind the MRO SD on the upper receiver rail, leaving sufficient clearance for your rear backup iron sight and proper 2.6-inch eye relief from your shooting stance.
- Confirm zero at 50/200 yards at 1x, flip the 3x magnifier into the optical axis, use the toolless centering turrets to center the 2.0 MOA red dot in the magnifier field of view, and set the diopter ring for crisp target focus.
Key Features
- Re-Engineered MRO SD Optical System: Upgraded multicoated 25mm objective lens eliminates magnification distortion and provides a wide, low-tube-effect sight picture.
- 2.0 MOA Red Dot & 8 Brightness Levels: Ambidextrous top-mounted rheostat dial offers 2 night vision-compatible settings, 5 daylight levels, and 1 super-bright setting with up to 2.5 years of continuous runtime on a single CR2032 battery.
- Compact 3x Magnifier with Flip-to-Side QD Mount: Features a 7.2-degree field of view (37.75 ft @ 100 yds), 2.6-inch eye relief, adjustable diopter (-2.5 to +2.0), toolless reticle centering, and 33-foot submersion rating.
- Dual Co-Witness Height Adaptability: Ships with a Trijicon Q-LOC™ Full Co-Witness mount and includes a magnifier riser spacer plate to match either Full or Lower 1/3 Co-Witness optic heights.
- Forged 7075-T6 Aluminum Durability: Fully sealed, nitrogen-purged construction with sub-flush 1/2 MOA turrets withstands 100-foot submersion and heavy duty recoil.
Product Specifications
- Brand: Trijicon®
- Model/Series: MRO® SD 1x25 Red Dot Sight & 3x Magnifier Combo
- MPN / SKU: MRO-C-2200367 / 2200367
- UPC: 719307621923
- Magnification & Objective: 1x (25mm Objective) / 3x Magnifier (21mm Objective)
- Reticle & Adjustments: 2.0 MOA Red Dot / 1/2 MOA per click (70 MOA Total Travel)
- Battery & Runtime: (1) CR2032 Lithium / Up to 2.5 Years continuous at Day Setting 3
- Housing Material & Finish: Forged 7075-T6 Aluminum / Matte Black Hardcoat Anodized
- Mounting Interface: MIL-STD-1913 Picatinny (Q-LOC™ Full Co-Witness & Flip-to-Side QD)
- Waterproof Rating: 100 ft / 30m (MRO SD) & 33 ft / 10m (3x Magnifier)
- Platform Compatibility: MIL-STD-1913 Picatinny Rifles, Carbines & Shotguns
- Country of Origin: USA